Available sizes

• 1 Gallon
• 5 Gallon

Direct to Metal Coating

• Utilizes 316L Stainless Steel Flake
• Self-priming DTM technology makes Endcor 8898-0402 an ideal choice for OEM applications
• Single component
• VOC content of 2.49 lbs/gal (298 g/l)
• Contains no isocyanates
• Provides excellent corrosion resistance
• Glossy UV resistant finish
• Continuous heat resistance up to 300°F (149°C)
• Suitable for shop or field application
• Ideal for process equipment such as tanks, racks, piping, pumps, and valves
• Brush, roller, or spray applied
• Available in one gallon and five gallon containers

8898-0402

Modified Silicone Alkyd

Metallic Gray

1

50±2

2.0 – 4.0 Mils (50 – 100 microns)

4.0 – 8.0 Mils (100 – 200 microns)

Theoretical coverage at 4.0 mils (100µm) DFT - 200 sq. ft. per gallon (4.9 m²/liter)

2 hours at 77°F

Allow 16-24 hours dry time between coats

Allow 24 hours dry time prior to shipping and handling

Weight per Gallon - 10.8 lbs. (4.89 kg.)

To ensure optimum long-term coating system performance, surfaces must be clean, dry and free from oil, grease, dirt, salts, welding flux, mill scale, rust, corrosion products, oxides, old paint, visible and non-visible contaminants or other foreign matter.

After completion of preliminary surface preparation work:

For mild corrosive environments clean all surfaces following “SSPC-SP 1 solvent cleaning standard” using a non-film forming solvent such as Dampney 170 cleaning solvent. Clean solvent and rags should be changed out frequently or as needed to ensure thorough cleaning.
For more aggressive corrosive environments to ensure optimum long-term coating system performance, surfaces must be clean, dry, and free from dirt, oil, grease, salts, welding flux, mill scale, rust, oxides, old paint, corrosion products, visible and non-visible contaminants, or other foreign matter.

Remove all surface imperfections that will induce premature coating system failure. Chip or scrape off weld splatter. Grind down sharp and rough welds, edges, gouges, slivers, and pits in accordance to NACE SPO178.

Abrasive blast surface per specification SSPC-SP- 10, (Near-White Metal Blast Cleaning), or per NACE Standard No. 2 to a profile depth of 1.0 - 2.0 mils (25-50µm). Abrasive used in blasting should be selected carefully from materials of mesh type and size required to produce the desired sharp anchor pattern.

If abrasive blasting is not permitted, prepare surface by power tool cleaning per SSPC-SP-11 (Power-Tool Cleaning to Bare Metal). Use an MBX Bristle Blaster or other type of power-tools to attain a sharp angular surface profile of 1.0 - 2.0 mils (25 - 50µm).

Note: Non-ferrous metals should be prepared in accordance to SSPC-SP-1 (Solvent Cleaning) with non-chlorinated solvents followed by preparation in accordance to SSPC-SP-16 or NACE 4 using non-metallic abrasives. A sharp angular surface profile depth of 1.0 - 2.0 mils (25 - 50µm). Consult Dampney Technical Service to determine the appropriate surface profile depth that is needed for the specific non-ferrous metal to be coated.
Customers are encouraged to test for suitability when applying over non-ferrous metals.

Redisperse any settled-out pigments by thorough mixing to a uniform homogeneous consistency with an explosion proof or air driven power mixer. Do not open containers until ready. Keep Lid on container when not in use.

Only thin Endcor 8898-0402 with Dampney 105 Thinner a maximum of 5% by volume. Dampney 105 thinner can be used if encountering dry spray and for other application related conditions. When reducing Endcor 8898-0402 for viscosity use thinners cautiously. The addition of a small amount of thinner could cause a large reduction in coating viscosity. Excessive thinning will impair wet film thickness and will cause runs and sags and change the VOC content of the coating. For conventional spray use adequate air pressure and volume to obtain proper atomization. Do not thin beyond federal, state and/or local VOC (volatile organic compound) emission regulations. Note: Use of other thinners not approved by Dampney may hinder product performance and void product warranty, whether expressed or implied.

Thoroughly flush all application equipment and hoses immediately after use with Dampney 105 Thinner. Dismantle spray equipment and clean parts and brushes with Dampney 105 Thinner.